• Modelers Alliance has updated the forum software on our website. We have migrated all post, content and user accounts but we could not migrate the passwords.
    This requires that you manually reset your password.
    Please click here, http://modelersalliance.org/forums/login to go to logon page and use the "Forgot your Password" option.

Thoughts on using a coffee mug warmer for decal water bowl?

helios

helios

Well-known member
I was curious what people's thoughts on these were. Obviously I'd need a suitable flat bottom ceramic bowl (which I have). It would certainly be more convenient than replacing the water every 10-15 minutes. A couple of the ones I was looking at list an operating temp of 131 degrees. I don't think that would be too warm, especially when you consider you'd be dealing with a larger volume of water, plus a greater surface area for increased heat loss. I'm thinking it might be worth a $20 experiment next time I'm up for a bout of decals.

Example of one I was looking at (just noticed this one is actually adjustable temp).

Cosori Mug Warmer - Amazon
 
In a perfect world, your water heater will dispense water between 120 and 125 degrees F. Cold water right out of the main is the same temperature as the the ground. 50 degrees or so. Your US Navy subjects will have LOTS of big decals, Yes? I advise warm water, since decals and paper have different rates of expansion. That's why they curl up in water. 70 to 80 degrees?
The opinion of M/A's resident Turd Surgeon.
 
Chris, the warmer looks good. I read it can be adjusted from 77 to 194 degrees. Only thing that might be a problem is it has a weight sensor on it that will shut it off if the weight is less than 11oz.

Thanks for posting about this, I might look in to one myself.
 
It is a good idea as I tried various temperatures on different decal sheets to see which would be best. Those experiments had me using much higher temperatures for decal paper available to Eastern Bloc companies (Techmod, Bilek, so on). As Rhino explained, the expansion of the paper (not the film) is what causes curling. The adhesive, if not warmed up on the Eastern Bloc paper, doesn't release the decal film with ink. This means the decal film stretches and fractures the ink (and sometimes the film as well). Usually, the paper expands, the adhesive loosens its grip on the paper before the tearing occurs. A dip in the very warm water (no more than three seconds) is all it needs and then placed on a folded paper towel as it curls and opens up ready to be slid off. Leaving them in the water too long can have the adhesive dissolve off the film.

Warm water also makes thick decal film pliable but heavy solvents (Solvaset, Micro-Sol, Super-Sol, et cetera) are needed to make them conform.

Regulating the water temperature is something I never considered so it is something I look forward to in your results.

Regards,
 
Frankly I don't think I have ever heard of heating the water for decals. Might be why I've had issues in the past.
:popcorn
 
I’ve always used warm water for decals. Don’t remember where I picked it up from. Ended up ordering one to try out. If it doesn’t pan out I’ll use it for my coffee. :)
 
This is what I use, you can select a number of temperatures. I just keep it on the workbench. The large volume of water stays warm for a long time and I pour small amounts in the little tub I soak decals in. Also good for tea or (ugh) instant coffee.

Water kettle


water kettle.jpg
 
Last edited:
rob hart said:
It helps. It seems to make more of a difference with lower quality decals. Personally, I think waterslide decals are old tech and we deserve something better.
Click to expand...

I wouldn't call many of the Eastern Block decal printers low quality, even though the decal will fracture if cold water is used. They simply need a different approach than those I was used to (MicroScale, SuperScale, Cartograf, et cetera). Archer has Nano Film and Eduard (among others) have waterslide decals from which the film can optionally be removed leaving the ink behind.

Regards,
 
That looks very cool. I would definitely give it a try. I have one for my cup now that does so so service. The one you pointed out looks to be better. Funny how its twice the price in Canada.
James
 
sharkmouth said:
I wouldn't call many of the Eastern Block decal printers low quality, even though the decal will fracture if cold water is used. They simply need a different approach than those I was used to (MicroScale, SuperScale, Cartograf, et cetera). Archer has Nano Film and Eduard (among others) have waterslide decals from which the film can optionally be removed leaving the ink behind.

Regards,
Click to expand...
This months Eduard Info magazine has an article on using their new decals. The demonstration used 2 identical P-51 sides with metal finish. Then identical decals were placed and one set had the clear coat removed. It was well done and quite informative. Here is the May Info link to the magazine PDF file.

Right click the link and "Save link as" to download.
 
I used the old on/off white plastic mug warmer back when I built models to the stage of applying decals. Turn it on and let the water warm up and then turn it off. Dang you young whippersnappers with your digital mug warmers! :oldguy:
 
20210510_201710.jpg
If you must warm up lots of water for large decals, this is Rival's 1-quart Hot Pot. Not only will it hold variable temperatures from tepid to boiling hot, but when snack time comes you can make macaroni & cheese or rice in it. Before my Sweetie moved in, (and brought a modicum of civilization to my BOQ) I used it to raise winter humidity levels. I've even used it to steam an ancient fur-felt hat I brought back from Australia 2/3rds of a lifetime ago. I advise against making Mac & Cheese and soaking your decals at the same time.
 
Huh... I've always used warm water for all the reasons mentioned above by others, but this is usually a starting point - i.e. I run warm water from the tap to start with, but by the time I'm done, it's cooled down to room temp. Hardly ever a problem since most of my modeling projects (armor) have very few decals.

However, this is such a simple and straightforward idea / solution! I think as with every good idea I come across, I'm gonna steal it!!
 
Barney said:
MP, You live in the deep south, your ground water is probably 75°!
Click to expand...
No today, temps down in the 40s for some reason.

I did some decals on the Comet last night, put the water in my metal bowl and hit the torch to it. heated up nicely and the decal slid on with no issues. Pictures later.
 
You must log in or register to reply here.

Similar threads

Old Dog
A G3M2 Nell in 1/48 the hard way
2 3 4
Replies
71
Views
7K
sharkman
sharkman
Sherman 18
Tamiya M48A3 Second Time Around
2 3 4
Replies
71
Views
8K
moon puppy
moon puppy
S
INSTRUCTION WALKTHROUGH - Airfix 1/24 Mosquito.
Replies
6
Views
1K
Scrodes
S
Back
Top