Some famous last words before one of my projects end up on my shelf (more like a room) of doom. Yes, I like the sound of that...
The ROOM of DOOM!
-
Modelers Alliance has updated the forum software on our website. We have migrated all post, content and user accounts but we could not migrate the passwords.
This requires that you manually reset your password.
Please click here, http://modelersalliance.org/forums/login to go to logon page and use the "Forgot your Password" option.
1/16th scale sFH 18 Howitzer
- Thread starter Heavens Eagle
- Start date
The ROOM of DOOM!
Heavens Eagle
Well-known member
Time for another small update as I have been working on this beastie on the weekends. This time the photos are telling the story.
For now I am now in adding the rivets mode, which actually isn't all that hard. I use a small piece of brass placed across a couple of rivets and then place the "new" rivet between them and add solvent. My mark 1C eyeball works well enough to center it that you probably couldn't tell even if you had a ruler. Thus easy peasy. I used a very sharp chisel blade to cut dozens of rivets from my little molded flats and put then in a nice small plastic container. So, new spot pick up rivet with tweezers. Place it along side bras "ruler" and add solvent while making sure it is centered.
I discovered in the process that I will have to make a mold for some larger rivets for the reinforced mounting ends. More fun.
For now I am now in adding the rivets mode, which actually isn't all that hard. I use a small piece of brass placed across a couple of rivets and then place the "new" rivet between them and add solvent. My mark 1C eyeball works well enough to center it that you probably couldn't tell even if you had a ruler. Thus easy peasy. I used a very sharp chisel blade to cut dozens of rivets from my little molded flats and put then in a nice small plastic container. So, new spot pick up rivet with tweezers. Place it along side bras "ruler" and add solvent while making sure it is centered.
I discovered in the process that I will have to make a mold for some larger rivets for the reinforced mounting ends. More fun.
Wow!
Brokeneagle
Master at Arms
Heavens Eagle
Well-known member
Have one trail almost done. Made a second "mold" for larger rivets that were used at the ends of the trail plus had to do more modification on the ends per the photos. Some was carving some was doing some creative work to get a circle opening in the right place so the rivets would place around it correctly. Once I get the one fully finished, I will take some photos and post some reference, before, after photos showing the crap I did. None of it has been all that hard, but has been a bit of a challenge to get right and looking right.
The fun part will be that I can set it up for transport, or FULLY lay it out for firing. Some of the mods I did end up being only to set it up for firing.
Is it perfect, oh hell no it isn't. Is it a lot closer, Yes it is. Out of the box it is probably only about 65% right. When I am done it should be closer to 96%.
The comparison photos will show the proofs. Still working on it.
The fun part will be that I can set it up for transport, or FULLY lay it out for firing. Some of the mods I did end up being only to set it up for firing.
Is it perfect, oh hell no it isn't. Is it a lot closer, Yes it is. Out of the box it is probably only about 65% right. When I am done it should be closer to 96%.
The comparison photos will show the proofs. Still working on it.
Heavens Eagle
Well-known member
Here is one trail basically done. I am sure there will be some piddley stuff that I have not addressed yet, plus the rods that are not yet placed on the sides.
With the rivet pattern I found that if I take and heat up a fair amount of sprue till it is REAL SOFT, then I place the pattern on my small arbor press and quickly place the melty sprue on the pattern and press it hard I end up with really good impressions. I made a flat square piece to put in the head of the press and mash it pretty hard. The thin areas around the rivets are about .020" thick.
Now to work on the other side. As this one is done and all figured out, the other side should go a lot quicker and easier.
With the rivet pattern I found that if I take and heat up a fair amount of sprue till it is REAL SOFT, then I place the pattern on my small arbor press and quickly place the melty sprue on the pattern and press it hard I end up with really good impressions. I made a flat square piece to put in the head of the press and mash it pretty hard. The thin areas around the rivets are about .020" thick.
Now to work on the other side. As this one is done and all figured out, the other side should go a lot quicker and easier.
